# What size wire do I need for 80 amps?

When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. The cable must contain one or two hot wires depending on your needs, one neutral wire, and one ground wire. Each wire should be 2-gauge in size.

When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. The cable must contain one or two hot wires depending on your needs, one neutral wire, and one ground wire. Each wire should be 2-gauge in size.

Similarly, what size wire is needed for 70 amps? There is a mininum wire size which is required based on the circuit breaker rating. That size is #4 copper or #2 aluminum. You get this number by using a quality voltage drop calculator by specifying the breaker amperage and a wire length of 1 foot.

In respect to this, what size wire do I need for 30 amps?

Any circuit fused for 30 amps must use a minimum of 10 ga copper or 8 ga alu. Longer runs may require an upgrade of wire size. In your case, use at least 10 copper for your welder regardless how far it is from the breaker panel.

What size is 100 amp wire?

You need a 3-3-3-5 copper SER cable to carry 100 amps (that’s three #3 gauge for the two hot wires and the neutral and a #5 gauge for the ground). If you want to use aluminum, you need at least #2 gauge or perhaps #1.

### What size wire is rated for 60 amps?

A kiln has a full load amp rating of 48 amps. 48 x 1.25 = 60 amps. A 60 amp breaker is a standard size. For these older kilns. 20 amps 12 gauge copper 60 amps 6 gauge copper 70 amps 4 gauge copper 80 amps 3 gauge copper 90 amps 2 gauge copper

### What gauge electrical wire do I need?

Wire Gauge The most common sizes you’ll find in residential work are 14-gauge and 12-gauge. Larger appliances such as electric stoves, electric water heaters, electric dryers and central air units will often use 10-, 8- or even 6-gauge wire.

### What size wire is needed for 125 amp service?

If you have a 125 amp breaker you need 125 amp wire. See the table here. You need to use the 75° column since no one makes a 90° breaker just yet. Since this is a single phase dwelling service you can use #2 AWG copper or 1/0 aluminum for a 125 amp service or main feeder.

200 amps

### How do you calculate circuit breaker wire size?

To find the current draw, you just divide this number by the voltage at which it operates, which is either 120 volts or 240 volts. Then, multiply this number by 125 percent. An easy way to do this is to divide it by 100 and then multiply it by 125. The rating of your circuit breaker must be larger than this total.

### What wire do you use for 200 amps?

So, for a 200-amp service, you would still be allowed to choose a 4/0 AWG aluminum or 2/0 AWG copper, but you would choose it from the 75 degree C column in Table 310.15(B)(16).

### What wire do I use for a 100 amp sub panel?

A 100 A sub-panel requires a two-pole 100 A breaker – if you want 100 A. You can use #4 AWG 75 deg C or 90 Deg C copper wire in conduit for a 100 A breaker provided the breaker is labeled for use with 75 deg C wire.

### Will 8 gauge wire carry 50 amps?

8 AWG may carry a maximum of 70 Amps in free air, or 50 Amps as part of a 3 conductor cable. David, if that cable is NM (Romex) then it actually cannot carry 50 amps.

### Can 12 gauge wire handle 30 amps?

A 30-amp breaker does not operate safely with a 12-gauge wire. The minimum wire size that is allowable for use with a 30-amp breaker is 10 gauge. A smaller gauge of wire indicates a larger diameter and the ability to carry more current safely. Twelve-gauge wire is acceptable with 20-amp or smaller circuit breakers.

### What size wire do I need for 10 amps?

• disabling your adblocker on The Engineering ToolBox! •• How to? American Wire Gauge (#AWG) Length (feet) Maximum Current (amps) 40 12 6 50 10 6 60 10 6

### Can 10 gauge wire handle 40 amps?

“Twelve-gauge wire is good for 20 amps, 10-gauge wire is good for 30 amps, 8-gauge is good for 40 amps, and 6-gauge is good for 55 amps,” and “The circuit breaker or fuse is always sized to protect the conductor [wire].”

### What size wire do I need for 25 amps?

This application requires a 25 amp circuit breaker. Wire size is a very important part in sizing a circuit. For circuit breakers up to 15 amps, use 14 gauge wire or larger. For a 20 amp breaker, use 12 gauge wire or larger.

### How many amps can 8 3 wire carry?

Size & AMP Ratings NM, TW, & UF WIRE (Copper Conductor) SE CABLE (Copper Conductor) 14 AWG – 15 AMPS 8 AWG – 50 AMPS 12 AWG – 20 AMPS 6 AWG – 65 AMPS 10 AWG – 30 AMPS 4 AWG – 85 AMPS 8 AWG – 40 AMPS 2 AWG – 115 AMPS